+- Kubes Corner (https://steroidsboard.com)
+-- Forum: Anabolics Forum (https://steroidsboard.com/forumdisplay.php?fid=7)
+--- Forum: Anabolic Steroid Discussion (https://steroidsboard.com/forumdisplay.php?fid=10)
+--- Thread: How to Inject Anabolic Steroids (/showthread.php?tid=20)
How to Inject Anabolic Steroids - Kubes - 10-10-2024
I don't think I injected deep enough....
If you think you injected into a layer of fat, don't worry. It will just take longer for the steroid to dissipate than it would if you had injected into the muscle. Eventually it will be absorbed. Don't let anyone tell you that you wasted it because that is not true.
I want to mix two different steroids and combine them into one syringe. How do I do this?
Let's say you want 1cc of deca and 1cc of test. First, draw 1cc of air and inject into your vial of deca. Withdraw 1cc of deca and pull the needle out. With the needle pointing up, draw 1cc of air into your syringe (your plunger will be at the 2cc mark - 1cc of deca in it and 1cc of air you just drew into it). With the needle pointing up, inject that 1cc of air into your vial of test. Withdraw 1cc of test. You now have 1cc of deca and 1cc of test in the same syringe. Don't forget to change the needle before you inject.
Instructions for first-timers.....
Step 1
Wash your hands.
Step 2
Wipe the top of the vial of medication for injection with an alcohol swab.
Step 3
Remove the needle guard from the needle and syringe, saving the needle guard. Be sure you are using a proper syringe for intramuscular injections. Pull back on the syringe plunger to draw up an amount of air equal to the amount of medication that your doctor has prescribed for injection. For example, if you want to inject 2ccs of oil, then pull back 2ccs of air.
Step 4
Holding the vial of medication in an upright position, insert the needle straight through the center of the rubber stopper in the vial. Then push the plunger to discharge all the air into the vial.
Step 5
With the needle in the vial, turn the vial upside down and hold it in one hand. The tip of the needle should be in the solution. Using your free hand, pull the plunger back in a slow, continuous motion until you have drawn into the syringe the amount of medication that your doctor has prescribed.
Step 6
If air bubbles have formed in the syringe, dislodge them by gently tapping the syringe with your free hand while continuing to hold the syringe and vial in the inverted position. Bubbles should rise to the top of the syringe, and then you can push them back into the vial by moving the plunger. Double check to make sure you have the correct amount of medication in the syringe. If necessary, draw more solution into the syringe.
Step 7
Remove the needle from the vial. With the needle pointing upwards, pull back on the plunger until all oil from the needle has been pulled back into the syringe. Unscrew needle from syringe and replace with a brand new, preferrably smaller needle. Replace needle guard.
Step 8
Prepare the injection site by cleaning the area with an alcohol swab. To do this start at the center, apply pressure, and cleanse in a circular motion working outward. Do not retrace your steps.
Step 9
Wait a few seconds until the alcohol has dried. This reduces the sting. Remove the needle guard from the needle and syringe. With the needle pointing upwards, tap the syringe to dislodge the air bubbles and push the air out of the needle until you see a tiny drop of oil start to form at the tip. Hold the syringe as you would a pencil.
Step 10
Holding the syringe at a right angle (perpendicular) to the prepared injection site and insert the needle.
Step 11
When the needle is in place, slowly pull back on the plunger to see if any blood flows into the syringe. If some blood does enter the syringe (a rare occurrence), remove the needle, replace the needle with a new one, find another area to inject. Repeat Step 8.
Step 12
If no blood enters the syringe, slowly inject the medication by gently pushing the plunger until the syringe is empty.
Step 13
Remove the needle quickly. Apply pressure to the injection site with your alcohol swab. You're done. Now go do the most important parts - eat, train, and rest!
RE: How to Inject Anabolic Steroids - Bubba - 10-25-2024
I'm not a fan of aspirating. I find it causes more harm than good, but it's a good practice for someone starting out still learning the sites.
In addition to the final step, dispose of properly!